In a year, 4822 people admitted to emergency rooms due to floor jack failure. It is not the reason for every home mechanic to get the jack stands they can afford. During the purchase of jack stands, you should consider a few things. Weight capacity for a set of two, the range of adjustable height, base width for how much room you have, how does adjusting mechanism works. Ratcheting stands seems more convenient, however selecting a pair of positions that use pin and hole or pin through, technology will ensure the highest safety rating.
You should remember that one pair of stands will only support a part of the weight of the vehicle. As a result, a three-ton pair is good enough for any personal vehicle on the market. Six ton of jack stand are available in the market, but in most cases, you are just wasting money on the more substantial and bulkier product.
You should always consider two factors, which are the durability of the product and the manufacturing quality. The base made from aluminum; you should search for steel pins or ratcheting devices which will give you service year after year without bending or breaking.
For the best value of money, here are three top-rated jack stand that have selected for their overall ranking and user satisfaction? But you need to ensure them as pair with a good quality floor jack to be able to get the stands underneath.
In the market there many popular jacks Stand brand available like-
- Torin Big Red T43004
- ESCO 10498 3-Ton Jack Stand
- ESCO 10498 3-Ton Jack Stand
- Hein-Werner HW93503 3-Ton Jack Stand
Best place to place jack stand when lifting Tundra
The Toyota 4Runner, Tundra, and Tacoma all have very similar jacking points. The manufacturer designed jacking points are the sections under the truck that to be strong enough to hold it up safely. For own safety, always user jack stand to secure the vehicle after raising it.
How to jack up your Toyota?
Step 1 – Locate jack points
To locate pointing jack the front or the rear of the truck. The best spot to raise the truck from is the center of the front cross member under the motor if you are increasing the front, and the center of the rear axle housing if you are raising the rear. The jack stand on the front point, the shaded section on the frame rails. On the back, they go on the rear axle.
Step 2 – Raise the vehicle
Align your jack in the middle of the jacking point, then start raising it. Once it touches the surface, be sure it is centered as it increases the vehicle. Slowly pump the jack until the car raised to the appropriate height.
Step 3 – Secure with jack stand
Once the vehicle lifted off the ground, secure the jack stand in their appropriate places
Once they're in place and extended, lower the jack very slowly until the vehicle rests on the jack stand. You will hear creeks as the car lays on the stands. Once the weight is entirely on the jack stands, you can pump the jack a little and leave it under the truck to help support the load in case a jack stand were to fail, but don't let it lift off the jack stands. As an added safety measure, if you take the wheel off the truck, you can lay it on the ground under it, which also saves you from tripping over it as well.
Nissan versa hatchback where is the best placement for jack stands
Before the place, the jack stand to make use of the bottom of the car immediately in front of the rear tire or directly behind the front tires. There will be a metal lip that extends downwards. The scissor jack has a notch that will fit this tab. Position the jack underneath the lift point and raises the car until the tire is no longer touching the ground.
Best place-to-place jack stand when lifting truck:
While changing the oil, it painless as long as you do it the right way. If they are not supported properly, it is dangerous after lifting the vehicle. For safety, both you and your vehicle here is a quick safety lesson on the proper use of hydraulic jacks.
It should keep in mind always use a stable surface while jacking up a vehicle. As you are putting a lot of weight on those jack stand, you need to make sure nothing will shift under that weight. Gravel, grass, and dirt are always wrong choices. Concrete is always bed. It is mandatory to park your vehicle and set the parking brake. You do not want your truck moving anywhere while you are working.
You need to make sure you have wheels chocks in place before placing the jack under the vehicle. You need to place the jack under the vehicle at a safe jacking that is the spots that will bear weight. And then lift the vehicle slowly.
Once the vehicle is high enough from the ground place, jack stand at safe jacking points. Again refer to an owner's or repair manual to find the safe jacking points on your vehicle. When jack stands are in place, lower your vehicle.
As soon as the vehicle is resting partially on the jack stand, stop lowering it. To test the stability and placement of the jack stand to place your hand on the vehicle and give it a little shake. As soon as you ensure the vehicle won't go anywhere, it would help if you stopped lowering the jack.